TY - JOUR
T1 - Influences of the constrained groove pressing on microstructural, mechanical, and fracture properties of brass sheets
AU - Shahmirzaloo, A.
AU - Hosseini, S.M.
AU - Siahsarani, A.
AU - Rahmatabadi, D.
AU - Hashemi, R.
AU - Faraji, G.
N1 - Publisher Copyright:
© 2020 The Author(s). Published by IOP Publishing Ltd.
PY - 2020/11/1
Y1 - 2020/11/1
N2 - Constrained groove pressing (CGP) was used for the production of fine-grained brass sheets in different conditions. The process was conducted up to two cycles on brass sheets at room temperature and then half cycle at the temperature of 200 °C. Optical microscopy (OM), scanning electron microscopy (SEM), microhardness measurement, and plane stress fracture toughness was used to investigate the microstructure, mechanical properties, and fracture behavior. Microhardness measurement showed the capability of the CGP process in increasing the hardness of the refined sheets. It also showed the inhomogeneity of the hardness along the thickness of the sample after the process. The Digital Image Correlation (DIC) technique was used to investigate the elastic and plastic factors of the sheets along with the major mechanical properties of samples. The results showed a slight increase and reduction in the Young modulus and Poisson's ratios after the process, respectively. Moreover, after two CGP cycles applying half cycle at the temperature of 200 °C did not show any significant effect on these values. The strength coefficient was as like as yield and ultimate strengths increased by increasing the number of the passes. However, processing at a higher temperature of 200 °C showed lower values for the parameters, as mentioned earlier, compared to the specimens processed at room temperature. The strain hardening index experienced a major reduction after the CGP process due to the effects of strain hardening. The anisotropy coefficient, which plays a critical factor in the severe deformation of sheets, was increased after the CGP process. However, this ratio decreased in higher passes or elevated temperatures. The highest anisotropy coefficient was obtained after the first cycle of the process. Moreover, SEM observation of the fracture surface showed shearing ductile rupture mode in the processed samples rather than ductile mode due to appearing of small and elongated dimples.
AB - Constrained groove pressing (CGP) was used for the production of fine-grained brass sheets in different conditions. The process was conducted up to two cycles on brass sheets at room temperature and then half cycle at the temperature of 200 °C. Optical microscopy (OM), scanning electron microscopy (SEM), microhardness measurement, and plane stress fracture toughness was used to investigate the microstructure, mechanical properties, and fracture behavior. Microhardness measurement showed the capability of the CGP process in increasing the hardness of the refined sheets. It also showed the inhomogeneity of the hardness along the thickness of the sample after the process. The Digital Image Correlation (DIC) technique was used to investigate the elastic and plastic factors of the sheets along with the major mechanical properties of samples. The results showed a slight increase and reduction in the Young modulus and Poisson's ratios after the process, respectively. Moreover, after two CGP cycles applying half cycle at the temperature of 200 °C did not show any significant effect on these values. The strength coefficient was as like as yield and ultimate strengths increased by increasing the number of the passes. However, processing at a higher temperature of 200 °C showed lower values for the parameters, as mentioned earlier, compared to the specimens processed at room temperature. The strain hardening index experienced a major reduction after the CGP process due to the effects of strain hardening. The anisotropy coefficient, which plays a critical factor in the severe deformation of sheets, was increased after the CGP process. However, this ratio decreased in higher passes or elevated temperatures. The highest anisotropy coefficient was obtained after the first cycle of the process. Moreover, SEM observation of the fracture surface showed shearing ductile rupture mode in the processed samples rather than ductile mode due to appearing of small and elongated dimples.
KW - anisotropy coefficient
KW - brass alloy
KW - constrained groove pressing
KW - digital image correlation
KW - mechanical properties
KW - microhardness test
KW - plane stress fracture toughness
UR - http://www.scopus.com/inward/record.url?scp=85096880108&partnerID=8YFLogxK
U2 - 10.1088/2053-1591/abc9f2
DO - 10.1088/2053-1591/abc9f2
M3 - Article
AN - SCOPUS:85096880108
SN - 2053-1591
VL - 7
JO - Materials Research Express
JF - Materials Research Express
IS - 11
M1 - 116526
ER -